Learning how to make a gravity bong is one of the easiest smoking hacks you can pull off at home. All you need are two plastic bottles, some aluminum foil, water, and a pin — no special equipment required. In this guide we walk you through the gravity bong two bottle method at home, step by step, so you can build one in minutes.
What Is a Gravity Bong?
A gravity bong uses water pressure and the weight of the smoke to force a thick, concentrated hit into your lungs. As you slowly pull the inner bottle up out of the water, a vacuum draws smoke down through the bowl and fills the chamber.
When you remove the bowl and push the bottle back down while inhaling, you get an intense, milky hit that is much stronger than a regular pipe or joint.
What You Need to Make a Gravity Bong
- 1 large plastic bottle (2-litre soda bottle or large water bottle) — outer container
- 1 smaller plastic bottle (500ml–1L) — inner chamber
- Aluminum foil
- Safety pin or bobby pin
- Box cutter or scissors
- Water
- Ground cannabis flower
How to Make a Gravity Bong: 5 Steps
Follow these 5 steps for the gravity bong two bottle method at home. Have everything ready before you start so the process is smooth.
Step 1: Prepare the Outer Container
Take the large plastic bottle and cut the top off — you are turning it into an open bucket to hold water. Fill it about two-thirds full with water and set it aside.
Step 2: Prepare the Inner Chamber
Take the smaller bottle and cut the bottom off. This bottle slides inside the large one and acts as the smoke chamber. The fit does not need to be perfect — just make sure the small bottle can slide up and down inside the large one without tipping over.
Step 3: Make the Aluminum Foil Bowl
Tear a small piece of aluminum foil and press it over the mouth of the inner (smaller) bottle to create a makeshift bowl. Press the centre down slightly and then fold the edges back up to create a raised lip — this prevents ground flower from falling off the edges.
Using a safety pin or bobby pin, poke 10 to 12 holes through the foil. This is your aluminum foil bowl gravity bong setup. A clean pattern of small holes gives you the best airflow.
Step 4: Load and Pull
Submerge the inner bottle (bottom-cut end down) in the water. Pack a small amount of ground flower onto the foil bowl. Hold a lighter over the bowl and slowly pull the inner bottle upward — do not pull it all the way out of the water.
As you lift, watch the smoke fill the chamber. Once the chamber is full, remove the foil bowl carefully so you do not drop it into the water.
Step 5: Take the Hit
Place your mouth over the opening of the inner bottle. Slowly push the bottle back down into the water while inhaling steadily. The water pressure pushes the smoke out and into your lungs.
Push slowly and steadily — if you push down too hard and too fast, you will get water in your mouth.
How to Hit a Gravity Bong Without Getting Water in Your Mouth
The biggest mistake beginners make is pushing the inner bottle down too fast. Here is how to hit a gravity bong without getting water in your mouth every time:
- Push slowly and steadily — no sudden movements. Slow, controlled pressure.
- Do not push all the way to the bottom — stop when most of the smoke is gone.
- Keep your mouth sealed — an airtight seal over the opening means no smoke escapes and the pressure builds evenly.
- Do not pull the inner bottle fully out when loading — if it comes out of the water, the smoke escapes and you lose the hit.
If you do get a small splash of water, just spit it out. It happens even to experienced users. The key is practice and a slow, steady push.
The Gravity Bong Bathtub 5-Gallon Method
If you have a bathtub, you can skip the two-bottle setup entirely and use the gravity bong bathtub 5 gallon method. Take a single large bottle — a 5-gallon water jug works perfectly — and cut the bottom off.
Submerge it in a full bathtub. Make your aluminum foil bowl on top, pack with flower, light it, and slowly pull the bottle up out of the water. The whole jug fills with a massive cloud of smoke.
Take the bowl off, put your mouth over the opening, and push down slowly. Hits from a 5-gallon gravity bong are extremely potent. If you have never done one before, start with a smaller amount of flower and take it easy — know your limits.
Frequently Asked Questions
How many holes should I poke in the foil?
Between 10 and 12 holes is the sweet spot. Too few and the airflow is restricted; too many and fine material can fall through. Use a safety pin or bobby pin for clean, consistent holes.
Does the size of the bottles matter?
Yes — the inner bottle must fit comfortably inside the outer bottle so it can slide up and down freely. A 500ml bottle inside a 2-litre works great. Just make sure there is enough water to keep the bottom of the inner bottle submerged as you pull it up.
Ground flower or whole buds — which is better?
Ground flower burns more evenly and produces a more consistent hit. Whole buds work but tend to cherry unevenly. A grinder is your friend here — the finer the grind, the better the airflow through the aluminum foil bowl gravity bong setup.
Is a gravity bong stronger than a regular pipe?
Yes, significantly. A gravity bong delivers a concentrated, pressurised hit that pushes more smoke into your lungs in one go. It is one of the most efficient ways to consume flower — which is why gravity bong hits feel much more intense than a standard pipe or joint. Treat it with respect, especially if you are new to it.
References
Learn More on Herbistry420
Purchase Links
Support Herbistry420 by visiting our Cannabis Apparel Store, we have t-shirts, hoodies, pants, towels, you name it!
Note: Some links are affiliate links. Purchases through these links support the channel at no extra cost to you.
Add comment