How to make a hash snake is one of those essential cannabis skills that unlocks a whole new level of smoke sessions. A hash snake — also called a hash rope or hash candy cane — is a thin coil of malleable hash that you place inside a joint to create the legendary hash hole joint. Once you know how to make a hash rope at home, you will never look at your hash stash the same way again.
What Is a Hash Snake?
A hash snake is simply hash that has been warmed and rolled into a rope or snake shape. It is used as a hash snake for a joint — specifically for making a donut hole joint or hash hole joint, where the hash melts down through the center of the joint as it burns, leaving a hole and delivering a significantly stronger hit than a regular flower joint.
You can use full melt or partial melt hash. Full melt is easier to work with since it is more pliable, but partial melt can work just fine with a bit more patience and heat. Avoid completely dried-out or very compressed brick hash as it is harder to form.
How to Make a Hash Snake: 4 Easy Steps
This parchment paper hash technique is the easiest and most reliable method for forming a hash snake at home. You only need three things: hash, parchment paper, and a lighter.
- Weigh out your hash. For a standard joint, aim for around 0.3 to 0.4 grams of hash. This gives you enough to form a workable snake that will sit nicely in the center of your rolling paper.
- Wrap in parchment paper. Place the hash on parchment paper and fold the paper over it. The parchment paper protects your fingers from the heat and gives you a smooth surface to roll against. If your paper keeps rolling up, fold the edges to keep it flat.
- Apply gentle heat with a lighter. Run a lighter under the parchment paper (not directly on the hash) for a few seconds at a time. This is how to roll hash into a snake — by warming it until it becomes malleable. Do not overheat; if you hold the flame too long the hash will ignite. Short bursts of heat, then work the hash with your fingers through the paper, then heat again.
- Roll and form the snake. Once the hash is warm and pliable, use the parchment paper to roll it against a flat surface, working it back and forth until it forms a uniform rope. If it breaks, just warm it again and press the pieces back together. The more time and patience you put in, the more uniform your hash snake will be.
How to Roll Hash Into a Snake: Tips and Tricks
When you learn how to make a hash snake, patience is everything. Here are a few extra tips from Fordee at Herbistry420:
- Keep it thin. The snake should be thin enough to sit in the center of a joint without causing the paper to bulge or tear.
- Work in short sessions. Heat the hash, work it for a few seconds until it starts to cool and become brittle again, then re-apply heat. Repeat until you have the shape you want.
- Replace torn parchment paper. If your paper tears, just swap it for a fresh piece and continue. The hash will not be damaged.
- Be safe. Keep your fingers at a safe distance from the flame. The hash and parchment paper are not immediately dangerous but always work carefully.
What to Do With Your Hash Snake
Once you know how to make a hash snake, the next step is putting it to use. The classic application is a hash hole joint — lay the hash snake for a joint right down the center of your rolling paper before rolling. As you smoke it, the hash melts and creates a hole in the center (the donut hole), amplifying the potency and flavour of every draw.
You can also shape it into a candy cane and place it inside a pipe or hash kettle for a different kind of hash experience. However you use it, making a hash rope at home with the parchment paper hash technique is a genuinely satisfying cannabis skill to master.
Frequently Asked Questions
What type of hash is best for making a hash snake?
Full melt hash is ideal as it becomes very pliable when warmed. Partial melt works with extra patience. Avoid low-grade or very compressed hash as it is harder to form into a uniform snake.
Do I need special tools to make a hash snake?
No special tools are needed. Just hash, parchment paper, and a lighter. Some people use a rubber mallet to beat the hash first to release oils and make it more malleable before applying heat.
How long does it take to make a hash snake?
Anywhere from 5 to 15 minutes depending on the type of hash and how uniform you want the snake to be. Drier or harder hash takes longer. The key is patience — short heat sessions alternated with shaping will get you there.
References
Learn More on Herbistry420
Note: Some links are affiliate links. Purchases through these links support the channel at no extra cost to you.
Add comment