Want to vape hash with DynaVap? It works — but there are a few technique differences from vaping dry herb that matter a lot. Fordee from Herbistry420 shows exactly how to do it: loading Afghani hash into a VapCap using a DIY secondary screen setup, dialling in the right amount of heat past the click, and keeping the tip clean with a disposable screen you can toss after each session. This is the complete guide to how to vape hash with a DynaVap, step by step.
What You Need to Vape Hash With DynaVap
- DynaVap VapCap — any M-series or Omni tip works
- Triple-flame torch lighter — gives more consistent, even heat than a single-flame lighter. A regular lighter works but results are less consistent.
- Hash — Fordee uses Afghani hash (traditional pressed hash). Dry sift hash also works well. Avoid very sticky live rosin or solvent-based extracts — those need a dab rig.
- 15mm pipe screens — standard mesh screens available on Amazon (~300 for $6–9). You’ll cut these down to size to create disposable secondary screens.
- Scissors — for trimming the screens to fit the DynaVap tip
- Ice pick or thin tool — to pop screens in and out of the tip
The Secondary Screen Method: Why It Matters for Hash DynaVap Sessions
The key to a clean hash dynavap session is the secondary screen. Hash leaves residue — sometimes a lot of it depending on the quality and stickiness. Without a secondary screen, that residue coats the inside of the tip and the stock screen, requiring deep cleaning after every hash session.
Fordee’s solution: cut a 15mm pipe screen down to fit the DynaVap tip using scissors. Load the hash on top of this secondary screen. After the session, pop out the secondary screen and throw it away. The stock screen beneath stays clean, and the tip stays almost pristine. Simple, cheap, and effective.
To cut the screens: hold the 15mm screen in your hand and trim in a circle with scissors until it fits inside the tip. Test the fit by dropping it in — it should sit flat without buckling. The first few might not be perfect, but you have ~300 screens in the pack so waste a few while learning.
How to Vape Hash With a DynaVap: Step by Step
Step 1 — Disassemble and Prep the Tip
Remove the cap, pull the tip off the body, and pop out the stock screen using an ice pick or similar thin tool. Reinsert the stock screen, then press your cut secondary screen on top of it. You now have two screens stacked — the stock screen at the bottom, the disposable secondary screen above it.
Step 2 — Load the Hash
Break off a small piece of hash — rice-grain to small pea size. Drop it on top of the secondary screen in the tip. Replace the tip onto the body, then put the cap over the loaded end to prevent the hash from falling out while assembling. Push the body back together and click it into place.
Step 3 — Prime With One Heat Cycle (Optional)
For hash, Fordee recommends one primer heat cycle before going for your full hit. Hold the DynaVap at 45 degrees, rotate it under the triple torch, and heat until it clicks. Remove the torch, let it cool for a few seconds (cooling it against another metal object speeds this up), then heat again for your actual hit. The primer helps the hash soften and begin vaporising evenly before you commit to a full draw.
Step 4 — Heat Past the Click (Just a Little)
Here is the key difference between vape hash dynavap-style versus flower: hash benefits from a slight amount of heat beyond the initial click. With flower, stopping exactly at the click works well. With hash, continuing for one to two seconds after the click gives denser, more satisfying vapor. Don’t go far past it — you’ll cross into combustion territory and lose the benefits of vaping entirely. Fordee describes it as a dance: “just to the right point.” Heat to click, count one-one-thousand, take your hit.
Step 5 — Use the Carb Hole to Control Airflow
Cover the carb hole (the small hole on the body) partially with your finger while drawing. Restricting airflow slightly increases the vapour density and makes the hit more satisfying. Experiment with how much coverage works for you — fully covered makes it too hard to pull, but partial coverage makes a noticeable difference.
5 Honest Tips to Vape Hash With DynaVap Better
- Use a triple-flame torch — the even heat wrap around the tip is especially important with hash, which needs consistent temperature more than flower does
- Small pieces hit better — a rice-grain of quality hash gives 2–4 solid hits. More than that and you risk uneven vaporisation or overflow onto the screens
- Let it cool between cycles — heating, clicking, and immediately reheating doesn’t give the hash time to vapourise properly. Give it 5–10 seconds between cycles
- Watch for harshness as the end signal — when the vapour starts tasting burnt or harsh, the hash is spent. Pop the screens, toss the secondary, and reload
- Use quality hash — traditional pressed hash and dry sift hash work best. Full melt bubble hash also works. The better the starting material, the better the hash dynavap experience
Cleaning Up After a Hash DynaVap Session
After the session cools (wait — don’t burn yourself), use an ice pick or thin tool to pop both screens out. Toss the secondary screen. The stock screen should be relatively clean. Check the inside of the tip — if there’s hash residue on the side wall, press the stock screen back in and it will scrape the wall clean on the way down. Reassemble and you’re ready for dry herb or another vape hash with DynaVap session.
For deeper cleaning when buildup accumulates over time, soak the tip and screens in isopropyl alcohol for a few minutes, rinse with warm water, and dry completely before use. Fordee keeps a dedicated container for spent ABV and hash residue — the secondary screen method keeps that container clean and the tip residue minimal.
Frequently Asked Questions
Can you vape hash with DynaVap without a secondary screen?
Yes, but you’ll need to clean the tip after every session. Hash leaves residue on the stock screen and the inside of the tip that builds up quickly. The secondary screen method makes hash dynavap sessions much more practical for regular use — toss the disposable screen and you’re done.
What types of hash work best in a DynaVap?
Traditional pressed hash (Moroccan, Afghani, Lebanese), dry sift hash, and bubble hash (5–6 star full melt) all work well when you vape hash with DynaVap. Very sticky live rosin or solvent-based concentrates (shatter, wax) are harder to work with and better suited to a dab rig or e-rig.
How do you know when the hash is finished?
When vapour becomes harsh, thin, or tastes burnt, the material is spent. With a rice-grain sized piece you’ll typically get 2–4 cycles. The darkened residue visible on the secondary screen when you pop it out confirms the hash has been fully vaporised. At that point, vape hash dynavap sessions are done — toss the screen and reload.
Do I need a special DynaVap tip for hash?
No — the standard M-series tip works perfectly. The secondary screen method detailed here works with any DynaVap tip. Some users prefer the Omni tip or Vong for their wider oven, but for most how to vape hash with a DynaVap situations, whatever tip you already own is fine.
References
Learn More on Herbistry420
Purchase Links
Use Coupon Code Herbistry to Save 10% over at DynaVap
• To pick up a DynaVap visit – https://bit.ly/4cRSzU5
• 200pcs Stainless Steel Pipe Filters – https://amzn.to/3IkK0F6
Add comment