This YLLVape IH 2.0 review covers everything you need to know about this induction heater for DynaVap devices — from what’s in the box to dialing in power settings, timer, insert height, and boost mode. If you want to level up your DynaVap experience with an electronic heater that gives you real control over your sessions, the YLLVape IH 2.0 delivers in a big way. Read on for 5 powerful tips to get the most out of it.
YLLVape IH 2.0 Review: What’s in the Box
The YLLVape IH 2.0 is an induction heater designed primarily for DynaVap devices (B series, M series, WoodWynd), though it also supports the Camouflet Convector via the included 11.5mm insert. In the box you get:
- The IH 2.0 unit with LCD screen, 3-button interface, and front magnet
- USB-C charging cable
- 8.5mm insert (for DynaVap devices) pre-installed
- 11.5mm insert (for Camouflet Convector)
Note: the IH 2.0 is NOT compatible with the DynaVap HyperDyn. It requires two 18650 batteries (not included) — use high-quality cells for best performance. The front magnet cools your Vap Cap quickly between sessions.
5 Powerful YLLVape IH 2.0 Tips to Dial In Your Sessions
In this YLLVape IH 2.0 review I found the biggest differentiator from other induction heaters is how much you can customize your experience. Here are 5 essential settings to master:
1. Power Setting: 30W vs 60W
The IH 2.0 adjusts from 30 watts to 60 watts. At 30W the DynaVap heats up slowly, giving you longer heat soak and more flavorful, low-temp hits. At 60W the device reaches click temperature rapidly — great for bigger clouds but requires precise timing to avoid combustion. Start at 30W while you learn the device, then experiment higher.
2. Timer Control (10 to 60 Seconds)
Double-click the center button to enter timer mode, then use the left/right buttons to set between 10 and 60 seconds. The timer starts counting down automatically when it detects your DynaVap inside the heater. This gives you precise, repeatable session control that torch heating simply cannot match.
3. Insert Height Adjustment
There’s a small metal tool in the battery compartment for turning the insert. Raising the insert means only the tip gets heated (faster click, lighter hit). Lowering means more of the body gets heated (more heat soak, fuller vapor). Insert height combined with power setting creates a deeply customizable experience unique to the YLLVape IH 2.0.
4. Boost Mode
Hold both the left and right buttons simultaneously to activate Boost Mode. This pushes the device beyond the standard 60W ceiling for extra power. The IH 2.0 is battery-dependent — high-quality 18650 cells are essential in boost mode. Use it when you want the fastest possible heat-up time.
5. The Front Magnet for Session Chaining
The small magnet on the front face of the IH 2.0 cools your Vap Cap quickly between sessions. Rest your DynaVap on it after a hit and the cap cools faster — letting you reload, unload ABV, or re-heat for the next session without burning your fingers. Simple, but surprisingly useful in practice.
YLLVape IH 2.0 Performance: 30W vs 60W Sessions
Testing the YLLVape IH 2.0 with a DynaVap B series handheld and an M7 through a bong: at 30W with 24-second timer, the first few hits were incredibly flavorful with no visible vapor — that low-and-slow heat soak extracting all the terpenes cleanly. Building heat across multiple sessions using the magnet between hits, visible vapor appeared by the third or fourth cycle.
Switching to 60W, the click came significantly faster and clouds were noticeably thicker and more visible. There’s a learning curve around timing — leave it in too long past the second click and you risk combustion, but once you dial in your 4-5 second post-click window, the results are impressive. Through the bong at 60W, the IH 2.0 produced thick, smooth hits that demonstrate this heater’s real capability.
Frequently Asked Questions
What DynaVap devices work with the YLLVape IH 2.0?
The YLLVape IH 2.0 is compatible with the DynaVap B series, M series, and WoodWynd using the included 8.5mm insert. The 11.5mm insert supports the Camouflet Convector. It is NOT compatible with the DynaVap HyperDyn. Always check compatibility before purchasing.
What batteries does the YLLVape IH 2.0 use?
The IH 2.0 uses two 18650 batteries (not included). Battery quality significantly impacts performance — especially in boost mode. Use high-drain 18650 cells from reputable brands for best results. Battery level is displayed graphically on the LCD screen.
Is there a learning curve with the YLLVape IH 2.0?
Yes — similar to learning to torch heat a DynaVap. Once you understand how power setting, timer, and insert height interact, it becomes second nature. The advantage over a torch is that every session is repeatable and adjustable. Most users find their preferred settings within a few sessions.
References
Learn More on Herbistry420
- Product Reviews — Vaporizers & Cannabis Accessories
- Smoke, Vape & Blaze — Cannabis Consumption Guides
- Dear Ganja Diary — Cannabis Lifestyle & Culture
Purchase Links
Save 10% with coupon code HERBISTRY at YLLVape:
🛒 YLLVape IH 2.0 Induction Heater
🛒 Decapper Stand (optional accessory)
Save 10% with coupon code Herbistry at DynaVap:
🛒 DynaVap Vaporizer
Save 15% with coupon code herb420 at Black Leaf:
🛒 Bong used in the video
Support the channel — Buy Me a Coffee / Beer / Spliff:
buymeacoffee.com/herbistry420
Herbistry420 Merch:
merch.herbistry420.com
Note: Some links are affiliate links. Purchases through these links support the channel at no extra cost to you.
Add comment